You have just bought a Fleximounts 4×8 overhead storage but don’t know how to install it? This blog is for you. We will guide you step-by-step to do Fleximounts 4×8 installation by yourself. Let’s check all steps right now!

Fleximounts 4×8 installation: Necessary tools

To install a Fleximounts 4×8 overhead storage at home, you need a pencil, power drill, tape measure, and stud/joist finder. Moreover, you may need a ladder to assemble the product against the wall. Eye protection is also essential to protect your eyes from damage.

Fleximounts 4×8 installation – Step 1: Attach ceiling brackets

Alternative A: To wooden ceiling joists

First of all, you have to use a stud finder to locate the wooden ceiling joists. Next, use the installation template included in the package to mark the mounting points.

Tips to use installation template:

Note that each ceiling bracket fastens to 2 separate joists. You should use a stud finder to locate the joists.

  • First, you should begin from the left side, place the template and mark two holes at the center of joists locations.
  • Second,  measure 48’’ from the left end and place the template again from point B. Mark two holes at the center of the joists locations.
  • Measure 48’’ from the right end and place the template again between point C and point D. Mark two holes at the center of the joists locations.

After marking the mounting points, you drill a 2.4’’ (60mm) depp 0.18” (4.5mm) diameter pilot hole at the center of each marked point.

Finally, install the ceiling brackets using a tapping screw and tighten with a wrench.

Alternative A: To wooden ceiling joists

All Fleximounts products come with a manual instruction to install it in just a few minutes. Try Fleximounts discount code here to save up to 20% your purchases!

Extra Fleximounts discount October 2020

Alternative B: To solid concrete ceiling

Similar to Alternative A, you first need to use the installation template to mark the mounting points. Then drill a 2.4” (60mm) deep 0.45” (12mm) diameter pilot hole at the center of each marked point.

The final step is to install the ceiling brackets using metal expansion bolts and tighten with a wrench. 

Alternative B: To solid concrete ceiling

Tips to use metal expansion bolts:

  1. Push the metal expansion bolts into mounting holes. Just make sure the holes are drilled with precise size.
  2. Unscrew the nuts and washers.
  3. Attach the ceiling brackets and screw in the nuts and washers.
  4. Fully tighten the nuts with a wrench.

Fleximounts 4×8 installation – Step 2: Assemble the vertical posts

In this step, you first need to determine hanging height and overlap posts as desired between 22” – 40” (560mm – 1010mm). Following this is to attach L-shaped/upright upper vertical posts with L-shaped/upright lower posts using bolts and nuts. Tighten with a wrench. 

Fleximounts 4x8 installation - Step 2: Assemble the vertical posts

You can take a look at 3 best Fleximounts garage storage for home 2020 to get more information about high-quality garage storage.

Fleximounts 4×8 installation – Step 3: Attach vertical posts to ceiling brackets

This is a very important step to do your Fleximounts 4×8 installation. First, attach L-shaped/upright vertical posts to ceiling brackets using bolts and nuts. Tighten with a wrench. Next, make sure the distance between the posts is fully consistent.

Fleximounts 4x8 installation - Step 3: Attach vertical posts to ceiling brackets

Don’t miss the chance to save up to $20 when ordering Fleximounts items by using Fleximounts promo code.

Fleximounts 4×8 installation – Step 4: Assemble and attach wire grids

In this step of Fleximounts 4×8 installation, you need to assemble the wire grids together and attach them using bolts and nuts. Remember to tighten with a wrench. Then attach the connecting plates at the joints, using the bolts and nuts. You also have to tighten with a wrench.

Fleximounts 4x8 installation - Step 4: Assemble and attach wire grids

Check 5 reasons for choosing Fleximounts overhead garage storage to get more information about Fleximounts overhead storage.

Fleximounts 4×8 installation – Step 5: Place and attach wire grid

First of all, insert the wire grid set. Keep in mind that the corners of the gird fit into the slot of the L-shaped vertical posts. Tighten the screws and nuts with a wrench. Secondly, attach the upright vertical posts with the side of the grid by tightening the screws and nuts with a wrench. 

Fleximounts 4x8 installation - Step 5: Place and attach wire grid

That is all the steps for your Fleximounts 4×8 installation. Just follow it carefully and you can assemble your overhead storage ceiling to save your space.

Conclusion

We just showed you how to do the Fleximounts 4×8 installation, hoping that you can install it for your home by yourself. Just remember to follow our tips to do it with ease. Don’t forget to use Fleximounts coupon to save up to 15% your orders when buying Fleximounts products.

Vanessa

Vanessa is a savings and deals expert at CouponRich.com. With interests in shopping, fashion and eco-friendly products, she aspires to help other shopaholics to pick up a bargain with latest coupon codes.